NEW-ERA STEEL TUBE HOLDING
NINGBO PIPEWAY TRADE CO.,LTD
| Place of Origin: | China |
|---|---|
| Brand Name: | New Era |
| Certification: | ISO9001,TS16949 |
| Model Number: | SAE J524 AMS 5050 E |
| Minimum Order Quantity: | 1 tons |
| Price: | Negotiation |
| Packaging Details: | Bundles Package, Wooden Box Package |
| Delivery Time: | 45 days |
| Payment Terms: | T/T |
| Supply Ability: | 3000 tons/month |
| Product Name: | Seamless Hydraulic Tubing | Delivery Condition: | Cold Drawn And Annealed Steel Tubes |
|---|---|---|---|
| OD Size: | 6-168mm | WT Size: | 1-20mm |
| Standard: | SAE J524 AMS 5050 E | Application: | Hydraulic Lines Tubing |
| Steel Material: | Low Carbon Steel SAE1010,St35.8 St37.4 | Heat Treatment: | Bright Annealed, Normalized, Annealing |
| Highlight: | SAE J524 Seamless Hydraulic Tubing,Annealed Seamless Hydraulic Tubing,Cold Drawn Seamless Hydraulic Tubing |
||
SAE J524 cold drawn and annealed seamless low-carbon steel pressure tubing intended for use as
hydraulic lines and in other applications requiring tubing a quality suitable for flaring and bending.
The the cold drawn steel tubes mainly for hydraulic steel tubing and cold drawn pressure tubing
SCOPE
This specification covers cold drawn and annealed seamless low carbon steel pressure tubing for use as hydraulic lines.
HYDROSTATIC TEST
Tubing supplied under this specification shall have been tested at not less than 1,000 lbs. hydrostatic pressure or higher
in case working conditions require.
CLEANLINESS
It is desired that the inside of tubing shall be bright, clean, and free from grease, drawing compounds, oxide, scale,
carbon deposits, and any contamination that cannot be readily removed by cleaning with alkaline cleaners or benzine.
CORROSION PROTECTION OF INTERIOR OF TUBES
The inside of the tubing having open ends shall be protected by a coating of clean oil to protect the interior of the tubing against corrosion during shipment and normal storage periods.The corrosion preventive oil used shall be such that, after extended storage periods, it can readily be removed with an alkaline cleaning solution or with benzine (Standard Solvent).
QUALITY
Tubing shall be free from defects and in accordance with the best commercial practice.
CHEMICAL COMPOSITION (percentage by weight)
The tubing shall conform to the following chemical analysis:
| Carbon……………0.18 max. | Phosphorus……….0.040 max. |
| Manganese……..0.30 -0.60 | Sulphur…………….0.050 max. |
Seamless low carbon steel tubing annealed for bending — Pressure type.
PHYSICAL PROPERTIES
The tubing shall conform to the following physical requirements
Tensile strength Lb/Sq. inch, minimum………………..45,000
Elongation in 2 inches, minimum………………………..35 percent*
For tubes with an OD of 3/8 inch and less and wall thickness of 0.035 inch and less, a minimum elongation of 30 percent is permitted.
A three inch section cut from the tubing shall not crack or show any flaws when flattened between parallel plates to three times the
wall thickness of the tube.
A section of tube approximately four inches in length with the ends burred shall withstand being expanded at one end over a polished
tapered mandrel having an included angle of 60 degrees until the actual average inside diameter is increased 30 percent.
The expansion test shall be made in a die in order to restrict the expansion of 30 percent. The axis of the mandrel should be paralled
to the axis of the tube during the expansion tests.
VARIATIONS
The diameter of the tubing shall not vary from that specified more than the following amounts:
|
OD Sizes
inches |
Outside Diameter, In.
|
|
|
Plus
|
Minus
|
|
|
Below 3-1/2 to 1-1/2 Incl.
|
0.010
|
0.010
|
|
Below 1-1/2 to 1/2 ID Incl.
|
0.005
|
0.005
|
|
Below 1/2 ID
|
0.003
|
0.003
|
When the outside diameter and wall thickness of 1/2 inch to 3-1/2 inch OD tubes are specified, the outside diameter shall conform to
the tolerances given in the above table, and the wall thicknesses shall not vary from that specified more than plus or minus 10 percent.
When less than 1/2 inch ID, the outside diameter shall conform to the tolerances given in the above table. The wall thickness shall not
vary from that specified more than plus or minus 15 percent.
PICKLE BRITTLENESS
Tubing which is pickled to remove scale shall be treated to eliminate pickle brittleness.
Tags:seamless hydraulic tubing,SAE J524 seamless tubing,cold drawn hydraulic tubing,cold drawn
pressure tubing,SAE J524 steel tubing,Low-carbon steel tubes.Low carbon steel tubing,J524 round
tubing,J524 metal tubing.